For Ford Focus 1.0L 2.0L 2.3L Volvo Xc60 2.0L High Pressure Fuel Pump LR025599

Description

The High Pressure Fuel Pump is used in the TFSI engine. Its function is to pressurize the fuel from the electric fuel pump to 150-200bar, which is easy to atomize and spray and adapt to the working characteristics of the TFSI engine. High pressure fuel pumps are generally driven by camshaft.
However, the high pressure fuel pump have a limited life.If you notice any of the following signs with your car:
1.Delayed start of the engine.
2.Hesitation or sputtering in acceleration between 2000 RPM to 4000 RPM.
3.High engine temperatures.
4.Vehicle stalling due to exertion or temperature.
5.Fuel pressure gauge reading low measurements.
6.Poor gas mileage
For Ford Focus 1.0L 2.0L 2.3L Volvo Xc60 2.0L High Pressure Fuel Pump LR025599
The
High Pressure Fuel Pump
is used in the TFSI engine. Its function is to pressurize the fuel from the electric fuel pump to 150-200bar, which is easy to atomize and spray and adapt to the working characteristics of the TFSI engine. High pressure fuel pumps are generally driven by camshaft.
However, the high pressure fuel pump have a limited life.If you notice any of the following
signs
with your car:
1.Delayed start of the engine.
2.Hesitation or sputtering in acceleration between 2000 RPM to 4000 RPM.
3.High engine temperatures.
4.Vehicle stalling due to exertion or temperature.
5.Fuel pressure gauge reading low measurements.
6.Poor gas mileage
This may indicate that you need to replace the fuel pump
High Pressure Fuel Pump Replacement Guideline:
High pressure oil pump removal steps
[Before removing high pressure fuel pump, release high pressure system fuel pressure]
Step 1:
Remove the engine cover, remove the air filter housing, and disconnect the negative connecting lead of the battery.
Step 2:
Remove the wire harness from the air duct, loosen the screw clamp, and unscrew the bolt as shown by the arrow in the drawing.
Step 3:
Loosen the hose clamp at the arrow on the way, and remove the pressurized air hose, and then remove the pressurized air hose.
Step 4:
Remove the high pressure pipe fixing clamp fastening bolt at the arrow shown in.Fixate the high pressure pipe connector as shown in the figure below with a wrench, then remove the union nut at the arrow and disconnect the high pressure pipe connection from the high pressure fuel pump.
Step 5:
Unplug the fuel pressure regulator connector as shown in the picture below, remove the fuel hose, unscrew the 2 fastening bolts as shown in the shears, and carefully pull out the high pressure pump.
Installation steps:
Step 1:
Test the O-ring of the high pressure pump and soak it slightly with clean engine oil. Check whether there is any damage before inserting the roller taper, and replace it if necessary. Load the roller tappet into the vacuum pump, and make sure that the convex on the roller tappet alines the groove on the vacuum pump during assembly.
Step 2:
Turn the crankshaft as far as possible until the roller tadpole is at the lowest point. Insert the high-pressure pump into the vacuum pump.
Step 3:
Cross tighten the fastening bolts by hand, and then cross tighten the fastening bolts with the prescribed torque of 20N.m. Insert the fuel hose and secure it with a spring clamp. Connect the fuel pressure regulator plug.
Step 4:
Soak the ball head of the high pressure pipeline with engine oil, install the high pressure pipeline, and tighten the lock nut of the fuel distributor with a wrench as indicated by the arrow in the drawing.
Step 5:
Use a wrench to fix the connector of the high pressure pipe, and then use another wrench to tighten the union nut of the high pressure pipe.
Step 6:
Install the high pressure pipe fixing clamp and tighten the fixing clamp bolt with torque of 5n.m.
Step 7:
Other installation can be carried out in the reverse order of disassembly.
Frequently Asked Questions
:
(1.)What is a high pressure fuel pump?
The high-pressure pump is supplied fuel by the electric pump. This pump generates the fuel pressure required for the high-pressure injector to provide optimum mixture of fuel and air directly into the cumbustion chamber.The HPP is typically located off of the fuel rail.
(2.)What causes high pressure fuel pump failure?
Fuel contamination: Fuel is jeopardized from corrosion, debris and moisture, which can all bring visible contaminants into the tank.
Clogged strainers/filters: The aforementioned contaminants eventually clog critical components including strainers, filters and the fuel pump itself.
Item Specifics
Drive Type
High Pressure Pump
Fuel Type
Gas
Injection Pump Type
Mechanical
Outlet Type
Threaded
Inlet Type
Quick Connect
Inlet Size
M14-1.5
Outlet Size
0.313
Fuel Injection Type
GDI
Outlet Quantity
2
Mounting Type
Bolted
Terminal Type
Blade
Terminal Gender
Male
Terminal Quantity
2
Gasket Included
No
Package Contents
1PC High Pressure fuel pump
Condition
New
Placement on Vehicle
External
Fitment Type
Direct Replacement
Material
Steel
Placement on Vehicle
On the engine
Interchange Part Number
AG9Z9350B Direct Injection High Pressure Fuel Pump
Warranty
2 Year
OE/OEM Part Number
LR 030860,0 261 520 151,AG9E9D376AB,5162174
Color
Silvery
Mounting Hardware Included
No
OE Spec or Performance/Custom
OE Spec
Custom Bundle
No
Brand
Fuel_Kingparts
Manufacturer Part Number
CB10693201S
Manufacturer Part Number
KF10693202ING
Payment
We only accept payment through PayPal.
Shipping
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
Returns
All of our brand new items come with a 60-Days money-back guarantee.
Contact Us
Any question, please contact us by email on working days.
Warning
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Best Sales
For Audi A5 Quattro A4 A5 Q5 A6 Premium TT Quattro High Pressure Fuel Pump
USD 92.80
High Pressure Fuel Pump For Land Rover Range Rover 5.0L 2010 2011 2012 2013-2016
USD 93.89
For VW Passat 3.6L 2007 2006 High Pressure Fuel Pump
USD 130.89
For Chevy Traverse GMC Acadia Buick Enclave 3.6L 2009-17 High Pressure Fuel Pump
USD 83.79
For 2013-15 Ford Escape Fusion 1.6L Direct Injection High Pressure Fuel Pump
USD 96.89
Newly Listed
For Audi A6 3.0L 5.2L Fuel Pump Moudle Assembly
USD 77.99
For 2000-2001 Ford Ranger V6 3.0L Electric Fuel Pump Moudle Assembly
USD 60.99
For 2000 2001 for Nissan for Sentra L4 1.8L Fuel Pump Electric E8427M
USD 20.99
For 3/8" NPT KMJ 2802 130GPH 14PSI Fuel Pump Electric
USD 59.99
For Kia Rondo EX Luxury 2008 2011 2012 Fuel Pump Moudle Assembly
USD 99.99
Terms & Contact
Payment Policy
Shipping Policy
Return Policy
FAQ
About Us
For Ford Focus 1.0L 2.0L 2.3L Volvo Xc60 2.0L High Pressure Fuel Pump LR025599
The
High Pressure Fuel Pump
is used in the TFSI engine. Its function is to pressurize the fuel from the electric fuel pump to 150-200bar, which is easy to atomize and spray and adapt to the working characteristics of the TFSI engine. High pressure fuel pumps are generally driven by camshaft.
However, the high pressure fuel pump have a limited life.If you notice any of the following
signs
with your car:
1.Delayed start of the engine.
2.Hesitation or sputtering in acceleration between 2000 RPM to 4000 RPM.
3.High engine temperatures.
4.Vehicle stalling due to exertion or temperature.
5.Fuel pressure gauge reading low measurements.
6.Poor gas mileage
This may indicate that you need to replace the fuel pump
High Pressure Fuel Pump Replacement Guideline:
High pressure oil pump removal steps
[Before removing high pressure fuel pump, release high pressure system fuel pressure]
Step 1:
Remove the engine cover, remove the air filter housing, and disconnect the negative connecting lead of the battery.
Step 2:
Remove the wire harness from the air duct, loosen the screw clamp, and unscrew the bolt as shown by the arrow in the drawing.
Step 3:
Loosen the hose clamp at the arrow on the way, and remove the pressurized air hose, and then remove the pressurized air hose.
Step 4:
Remove the high pressure pipe fixing clamp fastening bolt at the arrow shown in.Fixate the high pressure pipe connector as shown in the figure below with a wrench, then remove the union nut at the arrow and disconnect the high pressure pipe connection from the high pressure fuel pump.
Step 5:
Unplug the fuel pressure regulator connector as shown in the picture below, remove the fuel hose, unscrew the 2 fastening bolts as shown in the shears, and carefully pull out the high pressure pump.
Installation steps:
Step 1:
Test the O-ring of the high pressure pump and soak it slightly with clean engine oil. Check whether there is any damage before inserting the roller taper, and replace it if necessary. Load the roller tappet into the vacuum pump, and make sure that the convex on the roller tappet alines the groove on the vacuum pump during assembly.
Step 2:
Turn the crankshaft as far as possible until the roller tadpole is at the lowest point. Insert the high-pressure pump into the vacuum pump.
Step 3:
Cross tighten the fastening bolts by hand, and then cross tighten the fastening bolts with the prescribed torque of 20N.m. Insert the fuel hose and secure it with a spring clamp. Connect the fuel pressure regulator plug.
Step 4:
Soak the ball head of the high pressure pipeline with engine oil, install the high pressure pipeline, and tighten the lock nut of the fuel distributor with a wrench as indicated by the arrow in the drawing.
Step 5:
Use a wrench to fix the connector of the high pressure pipe, and then use another wrench to tighten the union nut of the high pressure pipe.
Step 6:
Install the high pressure pipe fixing clamp and tighten the fixing clamp bolt with torque of 5n.m.
Step 7:
Other installation can be carried out in the reverse order of disassembly.
Frequently Asked Questions
:
(1.)What is a high pressure fuel pump?
The high-pressure pump is supplied fuel by the electric pump. This pump generates the fuel pressure required for the high-pressure injector to provide optimum mixture of fuel and air directly into the cumbustion chamber.The HPP is typically located off of the fuel rail.
(2.)What causes high pressure fuel pump failure?
Fuel contamination: Fuel is jeopardized from corrosion, debris and moisture, which can all bring visible contaminants into the tank.
Clogged strainers/filters: The aforementioned contaminants eventually clog critical components including strainers, filters and the fuel pump itself.
Item Specifics
Drive Type :
High Pressure Pump
Fuel Type :
Gas
Injection Pump Type :
Mechanical
Outlet Type :
Threaded
Inlet Type :
Quick Connect
Inlet Size :
M14-1.5
Outlet Size :
0.313
Fuel Injection Type :
GDI
Outlet Quantity :
2
Mounting Type :
Bolted
Terminal Type :
Blade
Terminal Gender :
Male
Terminal Quantity :
2
Gasket Included :
No
Package Contents :
1PC High Pressure fuel pump
Condition :
New
Placement on Vehicle :
External
Fitment Type :
Direct Replacement
Material :
Steel
Placement on Vehicle :
On the engine
Interchange Part Number :
AG9Z9350B Direct Injection High Pressure Fuel Pump
Warranty :
2 Year
OE/OEM Part Number :
LR 030860,0 261 520 151,AG9E9D376AB,5162174
Color :
Silvery
Mounting Hardware Included :
No
OE Spec or Performance/Custom :
OE Spec
Custom Bundle :
No
Brand :
Fuel_Kingparts
Manufacturer Part Number :
CB10693201S
Manufacturer Part Number :
KF10693202ING
Payment
Shipping
Returns
Contact Us
Warning
We only accept payment through PayPal.
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
All of our brand new items come with a 60-Days money-back guarantee.
Any question, please contact us by email on working days.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
All rights reserved.